Quantcast
Jump to content


  • Sign Up, it's FREE!

    Welcome to RC Drone Forum! Use the main menu and search bar to navigate our site. It's always FREE to join our Drone Community and post in our forums, create your own Drone club, share your photos and videos and more. It's easy to get started and you can login with some of these popular social networks.

NEWS: iRangeX IRX4plus RF multimodule


Drone News

Recommended Posts

The popular RF multimodule for FrSky radios (and compatible for some Futaba) is updated with the IRX4plus: https://www.banggood.com/IRangeX-IRX4-Plus-2_4G-CC2500-NRF24L01-A7105-CYRF6936-4-IN-1-Multiprotocol-STM32-TX-Module-With-Case-p-1225080.html

Now there is a USB port to update the firmware for the STM32 MCU chip in order to add new supported protocol. The communication with the radio can be done directly via PPM connexion and a dial pot or via serial. In the last choice, all protocols/settings are available throught the radio OS. A must to have module !!!

null

null

null

null

null

null

Overview:
This 2.4G Multi-protocol TX Module is STM32 ARM microcontroller based module. All available protocols are included in serial mode. It is suitable for many brand of quadcopters, helicopters and airplanes.
This module integrate four RF chips (CC2500,NRF24L01,A7105,CYRF6936) into one single circuit board, it .supports a variety of remote control protocols ,such as Futaba S-FHSS, Walkera DEVO, Spektrum DSM2, DSMX, Flysky, Frsky, WLToys, Hubsan, Hisky, Esky , Assan etc. You can control your craft flexibility with it , and You will get much excellent experience with you favorite transmitter.

Specification:
Brand Name: iRangeX
Item Name: IRX4 Plus
Operating Voltage: 5-14V
Operating Current: <=100mA Operating Frequency: 2.4G ISM band RF Power: +22dBm MCU: STM32F103CBT6(128K ROM, 20K RAM) Weight: 45g Features:
Two operation modes: PPM mode and serial mode.
– When in PPM mode, there are 31 different protocols (protocol NO.0 is reserved for serial mode) mapping to the 16-position protocol selection switch on the module. They are listed in the default protocols table below, when the green light is off, you can use the switch to choose protocol NO. 1 to NO.15, when the green light is on, you can choose protocol NO.16 to NO.31.
– To turn on/off the green light, Please follow these steps:
Turn off you transmitter, point the protocol switch to ÿ0ÿ, hold and press the bind button of RF module, then turn on your transmitter, after 3 seconds, release the button.

Normal Use Operation in PPM Mode:
1. Install RF Module in position, Set PPM signal output on you transmitter.
2. According to the default protocols table, turn the arrow sign (the side with a vertical slot) of protocol switch to the proper number to choose protocol.
3. After finish binding operation, Power on your transmitter, the red light of RF module will be on, then RF module is ready to work , after that power on your receiver (or craft).
4. Protocol selection is done at the beginning of power up, so if you want to change protocol during operation, you should recycle the power.
5. The red light will blink slowly if there is no valid PPM signal.

Binding Operation in PPM Mode:
1. Power on your receiver, and set it to binding mode.
2. Hold and press the bind button of RF module, and then turn on your transmitter, after 3 seconds, release the button, you will see the red light flashing rapidly, then RF module is in binding mode, and the red light will go solid after binding.
3. Some protocols (eg: S-FHSS) donÿt have binding procedure on RF module, and some protocols (eg: hubsan, e010)will auto bind when power up.

Operation in Serial Mode:
When the green light is off, and the protocol switch is point to ÿ0ÿ, you can access serial mode. Transmitter that supports the er9X/erSky9X or Open TX firmware can work in this mode, The model protocol selection and binding is done from the Model Settings menu on the transmitter, For telemetry capable transmitters, the telemetry integration is done seamlessly with the transmitter firmware.
For more information, Please refer to the Link below.
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md

Notice:
– The jumpers and header attached is used for updating firmware of TX module through USB serial cable. Please remove them for normal use..
– Sometimes, you may need a power recycle when you choose a new protocol. for example, protocol changes from Q303 to HISKY.
– For FRSKY and S-FHSS protocol, you may need set the value of Fine or Option (in the Model Settings menu) properly to bind with your model. The value is varied, since itÿs partly depended on your model.

Package Included:
1x iRangeX IRX4 Plus TX Module

Cet article NEWS: iRangeX IRX4plus RF multimodule est apparu en premier sur Drone-Maniac !!!!!!!.

View the full article

Link to comment
Share on other sites



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...