Quantcast
Jump to content


  • Sign Up, it's FREE!

    Welcome to RC Drone Forum! Use the main menu and search bar to navigate our site. It's always FREE to join our Drone Community and post in our forums, create your own Drone club, share your photos and videos and more. It's easy to get started and you can login with some of these popular social networks.

Tattu 2305 2450KV Brushless drone Motors Review


DivenParker

Recommended Posts

Tattu 2305 2450KV Brushless Motors are made for FPV Racing drone. Each quadcopter motor has been carefully balanced and tested in the factory. Tattu 2305 2450KV motors are mainly suitable for 180-250mm quadcopter frame, the compatible propeller sizes are 5040 / 5045 two-blade or three-blade propeller, they made for FPV Racing drone. This is an interesting motor as a first entry as it bucks a few of the current trends in the dominant motors on the market.

 

Review:

  • The stator size is right in the middle at 2305, a bit smaller than the popular large motors, and a bit larger than the popular small motors.
  • The weight is right in the middle as well, coming in at just under 30g. This seems to be a motor of the middle ground on just about every front, with a fairly large air gap, square magnets, and multi-strand windings.
  • The shaft is retained with a c-clip, but it does retain the stronger single-piece hollow shaft design.
  • The machining quality and smoothness of this motor are top notch, with excellent finishing and no play.

Results

The results here are reflective of the middle ground this motor seems to occupy; very solid performance, especially for the smaller stator size and conservative kV.  The kV tested a tad lower than advertised coming in around 2390kv. One of the most noticable things about these results is the relatively flat performance across the range of props, only showing about 100g difference between the lighter 5″ props and the heaviest 5″ props. This is indicative of the larger air gap and shorter stator, where the lower torque loaded props respond well to the kV and the heavier loaded props bog the motor down a bit. That being said the performance here is very comfortably in the middle range, easily clearling 1300g on the mid to heavy load props, and staying around the 1200g mark even on the light props. It is also interesting to note that this motor barely got out of the low 30A range even on the heaviest props. It seems clear this motor was targeted towards that middle space of the average user, a pilot looking for a mid-weight motor that is usable on a broad range of props and a broad range of flying styles without being over-powered or killing the battery. This seems to have it the nail on the head for a general use, broad application motor that just about any pilot can find a use for.

Tattu 2305 2450kv Test Full Results

 

Tested KV: 2390kv

Weight: 29.7g

Stator W: 23mm

Stator H: 5mm

 

Test Environment:

XRotor 40A ESC

Timing: Med-high

Dither: 7

PWM: Damped Light

Venom 60A Power Supply

2Farad Caps x2 in Series

Custom Datalogger

TI TivaC Launchpad

Allegro ACS758-200B

Voltage Divider

EagleTree eRPM Sensor

Custom Thrust Stand w/ HX711

4 ms logging rate

Atmospheric Data (Typical)

Barometric pressure: 29-30 in

Ambient Temperature: 70-74 deg F

Humidity: 50-60%

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

  • Like 1
Link to comment
Share on other sites



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...