Jump to content


  • Sign Up, it's FREE!

    Welcome to RC Drone Forum! Use the main menu and search bar to navigate our site. It's always FREE to join our Drone Community and post in our forums, create your own Drone club, share your photos and videos and more. It's easy to get started and you can login with some of these popular social networks.

  • Announcements

    • Alex

      Start Your Own Drone Club   12/30/2017

      Now you can start your very own Drone Club here and have your own mini forum for your club! Visit the Clubs section in the main menu!
DivenParker

Tattu 2305 2450KV Brushless drone Motors Review

Recommended Posts

Tattu 2305 2450KV Brushless Motors are made for FPV Racing drone. Each quadcopter motor has been carefully balanced and tested in the factory. Tattu 2305 2450KV motors are mainly suitable for 180-250mm quadcopter frame, the compatible propeller sizes are 5040 / 5045 two-blade or three-blade propeller, they made for FPV Racing drone. This is an interesting motor as a first entry as it bucks a few of the current trends in the dominant motors on the market.

 

Review:

  • The stator size is right in the middle at 2305, a bit smaller than the popular large motors, and a bit larger than the popular small motors.
  • The weight is right in the middle as well, coming in at just under 30g. This seems to be a motor of the middle ground on just about every front, with a fairly large air gap, square magnets, and multi-strand windings.
  • The shaft is retained with a c-clip, but it does retain the stronger single-piece hollow shaft design.
  • The machining quality and smoothness of this motor are top notch, with excellent finishing and no play.

Results

The results here are reflective of the middle ground this motor seems to occupy; very solid performance, especially for the smaller stator size and conservative kV.  The kV tested a tad lower than advertised coming in around 2390kv. One of the most noticable things about these results is the relatively flat performance across the range of props, only showing about 100g difference between the lighter 5″ props and the heaviest 5″ props. This is indicative of the larger air gap and shorter stator, where the lower torque loaded props respond well to the kV and the heavier loaded props bog the motor down a bit. That being said the performance here is very comfortably in the middle range, easily clearling 1300g on the mid to heavy load props, and staying around the 1200g mark even on the light props. It is also interesting to note that this motor barely got out of the low 30A range even on the heaviest props. It seems clear this motor was targeted towards that middle space of the average user, a pilot looking for a mid-weight motor that is usable on a broad range of props and a broad range of flying styles without being over-powered or killing the battery. This seems to have it the nail on the head for a general use, broad application motor that just about any pilot can find a use for.

Tattu 2305 2450kv Test Full Results

 

Tested KV: 2390kv

Weight: 29.7g

Stator W: 23mm

Stator H: 5mm

 

Test Environment:

XRotor 40A ESC

Timing: Med-high

Dither: 7

PWM: Damped Light

Venom 60A Power Supply

2Farad Caps x2 in Series

Custom Datalogger

TI TivaC Launchpad

Allegro ACS758-200B

Voltage Divider

EagleTree eRPM Sensor

Custom Thrust Stand w/ HX711

4 ms logging rate

Atmospheric Data (Typical)

Barometric pressure: 29-30 in

Ambient Temperature: 70-74 deg F

Humidity: 50-60%

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

Tattu-2305-2450KV-Brushless-Quadcopter-M

  • Like 1

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

    • By CBF America
      Hello! I have recently received my patent for a unique, practical, and very effective personal cooling device I am calling the Cool body fan. I believe it would be best to utilize a drone propeller, motor, and battery, and have a variable speed knob as well. I am seeking references to exactly what parts may be best to use. The Constraints and attributes needed for the system are as follows:
      ---The propeller must be 6" to 7" in diameter.
      ---The more quiet the propeller is, the better.
      ---The more quiet the motor is, the better.
      ---Between the motor, propeller, and battery, I only need it to blow about as much air as the Ryobi fan (picture attached). 
      ---I would like a run time of at-least 4 hours on one charge.
      I wont bother breaking down the design of the Cool Body Fan, but these attributes should be enough to go by.
      Please feel free to provide any input or references that may be helpful. Ideally I'd like to find a specific part on the market for each component that people have recommended me and buy these for my third prototype.
      Also, is it possible to simply wire a knob between a drone motor and battery to act as a speed dial? Let me know your thoughts.
      Thank you very much!



×